Sikafloor® Marine-100

Lightweight self-leveling primary deck covering mortar for interior decks

Sikafloor® Marine-100

Sikafloor® Marine-100  is a 1-component lightweight self-leveling mortar based on polymer modified cement.
Sikafloor® Marine-100 is tested according to FTP Code system and approved according to the IMO Marine Equipment Directives  

  • Lightweight leveling mortar
  • One component, ready to mix
  • Easily applicable
  • Good leveling properties in thin layers
  • Can be pumped
 
Show all documents

Find this product in your country

Go

Overview

PRODUCT BENEFITS

  • Lightweight leveling mortar
  • One component, ready to mix
  • Easily applicable
  • Good leveling properties in thin layers
  • Can be pumped
 

Areas of Application

Sikafloor® Marine-100 is applied on interior decks, to level the surface prior to the application of deck finishing materials such as: carpets, tiles, parquet, rubber and vinyl. It is suitable for application in dry and wet accommodation areas exept for galleys. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.  

Packaging

Bag

14 kg

 

Product Details

Chemical base

Polymer modified cement mortar

Color

Grey

Cure mechanism

Hydraulic

Density

mixed

cured

1.2 kg/l

0.9 kg/l

Mixing ratio

per 14 kg bag

5.9 ─ 6.4 liter

Substrate temperature

5 ─ 30 °C

Application thickness

max.

10 mm

Coverage

per 14 kg bag at layer thickness 1 mm

15 m2

Working time (CQP599-9)

30 minutes A

Ready to walk on (CQP600-3)

depending on humidity and ventilation

12 hours A

Compressive strength (CQP599-2)

7 MPa B

Flexural strength (CQP599-1)

4.2 MPa B

Modulus of elasticity in compression (CQP599-6 / EN 13412)

2 GPa B

Linear shrinkage (CQP599-5)

0.04 % B

Shelf life

12 months C

CQP = Corporate Quality Procedure

A) 23 °C / 50 % r. h.

B) after 28 days

C) stored in a dry, cool place below 25 °C

CURE MECHANISM

Sikafloor® Marine-100 cures by way of hydraulic curing.

Application

Surface preparation

For leveling applications, the surface has to be clean, free from dust, grease, oils and other substances, which may impair adhesion. Rust has to be removed with a steel brush or other appropriate means, followed by vacuum cleaning.
The surface has to be primed with Sikafloor® Marine Primer C using a long hair roller. After drying of the Sikafloor® Marine Primer C, Sikafloor® Marine-100 may be applied.
Sikafloor® Marine-100 applications on aluminum or zinc rich shop primer coated decks, require a tie coat of SikaCor® ZP Primer or another suitable tie coat prior the priming step with Sikafloor® Marine Primer C.

Application

Apply the mortar with a steel board or a straight edge. Sikafloor® Marine-100 can also be applied by pinrake.
Sikafloor® Marine-100 has to be applied within 20 minutes after mixing. At temperatures above 30 °C the open time will be reduced to 10 minutes or less.
For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry.

Removal

Excess material can best be removed before curing with a trowel wipe or water.

Fresh Sikafloor® Marine-100 may be removed from tools and equipment with water. Once cured, the material can only be removed mechanically.
Exposed hands and skin shall be washed immediately with water. Use a suitable skin protection hand cream.

Application limits

For applications on slooping surfaces > 1 % contact the Technical Department of Sika Industry.

Documents