Sikaflex®-668 + SikaBooster® P-50
Sikaflex®-668 + SikaBooster® P-50 is based on Purform®, a polyurethane with less than 0.1% monomeric diisocyanate for better health protection and occupational safety. Sikaflex®-668 + SikaBooster® P-50 is an accelerated adhesive system specifically designed for the rail industry. The curing of Sikaflex®-668 + SikaBooster® P-50 is accelerated by SikaBooster® P-50 which makes it largely independent of atmospheric conditions. It is suitable for assembly bonding and glazing applications. Its good resistance to weathering and to a wide variety of cleaning agents makes it an ideal solution for use in exterior joints in the rail industry.
- Less than 0.1 % monomeric diisocyanate for better health protection and occupational safety
- Very good weathering stability
- Resistant to a wide variety of cleaning agents
- Passes EN45545 R1/R7 HL3, NFPA 130, BSS 7239
- Fast-curing by Booster Technology
- Phthalate-free
PRODUCT BENEFITS
- Less than 0.1 % monomeric diisocyanate for better health protection and occupational safety
- Very good weathering stability
- Resistant to a wide variety of cleaning agents
- Passes EN45545 R1/R7 HL3, NFPA 130, BSS 7239
- Fast-curing by Booster Technology
- Phthalate-free
Areas of Application
Sikaflex®-668 + SikaBooster® P-50 is designed for assembly and direct-glazing applications in the rail and commercial vehicle industry. It exhibits very good tooling and application properties. With its superior resistance to a wide range of cleaning agents combined with outstanding weathering resistance, it can be used for exterior joints. The use of SikaBooster® P-50 provides rapid attainment of strength and early adhesion development. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-668 + SikaBooster® P-50 on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed ensuring adhesion and material compatibility.Product Details
| Chemical base | Polyurethane (Purform®) | |
| Color (CQP001-1) | Black | |
| Cure mechanism | Moisture-curing A | |
| Density (uncured) | Adhesive | 1.3 kg/l |
| Booster content | by volume by weight | 2.0 % |
| Non-sag properties | Good | |
| Application temperature | 10 ─ 35 °C | |
| Open time (CQP526-1) | 40 minutes B | |
| Early tensile lap-shear strength (CQP046-1 / ISO 4587) | (see table 1) | |
| Shrinkage (CQP014-1) | 1 % | |
| Shore A hardness (CQP023-1 / ISO 48-4) | 60 | |
| Tensile strength (CQP036-1 / ISO 527) | 8 MPa | |
| Elongation at break (CQP036-1 / ISO 527) | 500 % | |
| Tear propagation resistance (CQP045-1 / ISO 34) | 12 N/mm | |
| Tensile lap-shear strength (CQP046-1 / ISO 4587) | 5 MPa | |
| Service temperature (CQP513-1) | -50 ─ 90 °C | |
| Shelf life (CQP016-1) | Adhesive (pail / drum) | 6 months C |
| Mixer | Statomix MS 13/18 G |
| CQP = Corporate Quality Procedure | A) provided by SikaBooster® P-50 | B) 23 °C / 50 % r. h. | C) stored below 25 °C |
CURE MECHANISM
Sikaflex®-668 + SikaBooster® P-50 cures by reaction with moisture provided by SikaBooster® P-50 and is largely independent from atmospheric moisture. For typical strength build up data see table below.
| Time [h] | Tensile lap-shear strength at 23 °C [MPa] |
| 2 | 1 |
| 3 | 2.5 |
| 4 | 3 |
| 6 | 4 |
Table 1: Strength build-up of Sikaflex®-668 + SikaBooster® P-50
CHEMICAL RESISTANCE
Sikaflex®-668 + SikaBooster® P-50 is generally resistant to fresh water, seawater, diluted acids and diluted caustic solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic acids, glycolic alcohol, concentrated mineral acids and caustic solutions or solvents.
It is resistant to a wide range of rail cleaning agents if used according to the guidelines of the manufacturer. Some rail cleaning agents contain aggressive chemicals such as phosphoric acids which may influence the durability of Sikaflex®-668 + SikaBooster® P-50 significantly. Therefore it is of highest importance to limit the exposure time to a minimum, observe correct dilution of cleaning agent and to perform a thorough rinsing after the cleaning process. Test newly introduced cleaning agents.
The above information is offered for general guidance only. Advice on specific applications will be given on request.
Application
Surface preparation
Surfaces must be clean, dry and free from grease, oil, dust and contaminants. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. All pre-treatment steps must be confirmed by preliminary tests on original substrates considering specific conditions in the assembly process.
Note: The maximum primer flash-off time is limited to 8 hours for Sikaflex®-668 + SikaBooster® P-50 at temperatures above 30 °C. The primer must then be reactivated with Sika® Aktivator-100 prior the bonding process.
Application
Sikaflex®-668 + SikaBooster® P-50 needs to be processed with an adequate dispensing system. The mixer type must be respected (see table Typical Product Data).
Sikaflex®-668 + SikaBooster® P-50 can be applied between 10 °C and 35 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. To ensure a uniform thickness of the bondline it is recommended to apply the adhesive in form of a triangular bead (see figure 1).
Figure 1: Recommended bead configuration
The open time is significantly shorter in hot and humid climate. The parts must always be joined within the open time. As a rule of thumb, a change of + 10 °C reduces the open time by half.
For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry.
Tooling and finishing
Tooling and finishing must be carried out within the open time of the adhesive. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility.
Removal
Uncured Sikaflex®-668 + SikaBooster® P-50 may be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically.
Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water.
Do not use solvents on skin.